*IMPORTANT: If venting in an non-insulated attic space, or in a cold climate, insulated flexible duct is strongly recommended for condensation issues.

The TD-Mixvent series of in-line duct fans have been specially designed to maximize the airflow performance with minimal noise levels within the smallest and most compact of casing sizes. This makes it the ultimate solution for small to medium sized ventilation installations which require a high air-flow to pressure ratio and occupy only the minimum space possible. Example: false ceiling voids, cupboards and many other limited space environments. All models include a "removable body" feature that enables the motor-impeller assembly to be completely removed or replaced without the need to interfere with the attached ducting. The TD fans are ideally suited for a wide range of residential, commercial and industrial exhaust and intake ventilation applications. Typical applications would include the following.

RESIDENTIAL:

• Bathrooms
• Warm or Cool Air Transfer
• Kitchen Range Hoods
• Utility Rooms

COMMERCIAL:

• Locker Rooms
• Conference Rooms
• Bars & Restaurants
• Cafeterias
• Offices
• Make-Up Air Applications

INDUSTRIAL:

• Welding Fume Extraction
• Spot Ventilation
• Equipment Cooling
• Workshops & Smoking Areas

CONSTRUCTION:

Models 100, 100X, 150 and 200X are manufactured in tough reinforced plastic, the fan duct connection flanges are manufactured from reinforced plastic, except for the 200 and 200x which are constructed from epoxy-polyester coated metal.

IMPELLERS:

The impeller blades for models 100,100x, 150 and 200x are molded in tough ABS plastic. Model 200 is metal.

MOTORS:

Model 100 is Single-phase, 120V 60Hz, shaded pole induction asynchronous motor in die cast aluminum. All motors include direct two speed connection and are also suitable for voltage speed control.

• Class II electrical insulation
• IP 44 Protection
• Class B Motor Insulation
• Safety auto reset Thermal Overload Protection (fuse type)
• Self-lubricating sleeve bearings.
• Suitable for working airstreams up to 104° F (40°C).

*Performance certified is for installation type D-Ducted inlet, Ducted outlet. Performance ratings do not include the effect of appurtenances(accessories). Speed (RPM or RPS) shown is nominal. Performance is based on actual speed of test.

DIMENSIONAL DATA: (inches)

X = 5 15/16
A = 9 1/8
B = 5 7/16
C = 3 3/4
D = 3 7/8
E = 3 1/4
F = 3 3/4
G = 1 7/8
H = 2 1/16

*IMPORTANT: If venting in an non-insulated attic space, or in a cold climate, insulated flexible duct is strongly recommended for condensation issues.

The TD-Mixvent series of in-line duct fans have been specially designed to maximize the airflow performance with minimal noise levels within the smallest and most compact of casing sizes. This makes it the ultimate solution for small to medium sized ventilation installations which require a high air-flow to pressure ratio and occupy only the minimum space possible. Example: false ceiling voids, cupboards and many other limited space environments. All models include a "removable body" feature that enables the motor-impeller assembly to be completely removed or replaced without the need to interfere with the attached ducting. The TD fans are ideally suited for a wide range of residential, commercial and industrial exhaust and intake ventilation applications. Typical applications would include the following.

RESIDENTIAL:

• Bathrooms
• Warm or Cool Air Transfer
• Kitchen Range Hoods
• Utility Rooms

COMMERCIAL:

• Locker Rooms
• Conference Rooms
• Bars & Restaurants
• Cafeterias
• Offices
• Make-Up Air Applications

INDUSTRIAL:

• Welding Fume Extraction
• Spot Ventilation
• Equipment Cooling
• Workshops & Smoking Areas

CONSTRUCTION:

Models 100, 100X, 150 and 200X are manufactured in tough reinforced plastic, the fan duct connection flanges are manufactured from reinforced plastic, except for the 200 and 200x which are constructed from epoxy-polyester coated metal.

IMPELLERS:

The impeller blades for models 100,100x, 150 and 200x are molded in tough ABS plastic. Model 200 is metal.

MOTORS:

Model 100 is Single-phase, 120V 60Hz, shaded pole induction asynchronous motor in die cast aluminum. All motors include direct two speed connection and are also suitable for voltage speed control.

• Class II electrical insulation
• IP 44 Protection
• Class B Motor Insulation
• Safety auto reset Thermal Overload Protection (fuse type)
• Self-lubricating sleeve bearings.
• Suitable for working airstreams up to 104° F (40°C).

*Performance certified is for installation type D-Ducted inlet, Ducted outlet. Performance ratings do not include the effect of appurtenances(accessories). Speed (RPM or RPS) shown is nominal. Performance is based on actual speed of test.

DIMENSIONAL DATA: (inches)

X = 5 15/16
A = 9 1/8
B = 5 7/16
C = 3 3/4
D = 3 7/8
E = 3 1/4
F = 3 3/4
G = 1 7/8
H = 2 1/16